Reciprocating Pump Simulator
Single & double acting, duplex & triplex in 2D and 3D — indicator diagram, separation & air vessels — Simulate • Explore • Practice • Quiz
Display Controls
Σ Live working — from the pump on screen
1 Overview
The simulator is a reciprocating (piston) pump drawing water from a sump and delivering it to a tank. A crank, connecting rod and crosshead move the piston; two spring-loaded disc valves let the water in and out. Every pressure on screen comes from one solved revolution: the exact slider-crank, the acceleration head and the friction head of each pipe, and the air vessels when they are fitted. It has four modes: Simulate, Explore, Practice and Quiz.
2 Getting Started
Pick a pump type in card 1 (Single acting, Double acting, Duplex, Triplex) or a preset, then set the crank speed, bore and stroke. Card 2 sets the suction lift, the delivery head and the length and bore of each pipe; card 3 fits the air vessels and sets their gas volume, the slip and the separation head. Every slider has a number box beside it for an exact value.
The page always opens in the 2D view. The 2D | 3D switch is at the left of the bar under the picture. Add ?view=3d to a link to open the 3D pump. In 3D the part names are off at first: tick Labels in 3D under Display Controls to show them.
3 Simulate Mode
- The 2D view shows the pump in section with the water moving as it really does (streaks travelling at the pipe velocity, jets through the open valves, the water filling and emptying the cylinder behind the piston, the outlet pouring into the tank), the valves lifting with the flow, gauges at the pipe connections, the live indicator diagram of cylinder 1 and the discharge against crank angle. Heights are printed, not drawn to scale. Tick Colour water by pressure in Display Controls to tint the water by its absolute pressure instead (violet near separation, blue at atmospheric, teal to amber above).
- Turning the crank by hand: drag the crank disc (2D) or the flywheel (3D), or use the arrow keys with the picture focused. Space pauses and runs.
- Above 30 rpm the motion is slowed on screen and the factor is printed; the numbers are always at the real speed.
- ▶ Explain a revolution stops at six points of the cycle and explains the pressure in the cylinder at each.
- The 3D view: drag the flywheel to turn the crank, drag anywhere else to orbit, Ctrl + scroll or pinch to zoom. Whole, Valves and Crank move the camera; Cut the pump open in Display Controls shows the inside.
4 Separation, Negative Slip and Air Vessels
If the cylinder pressure would fall below the separation head (2.5 m of water absolute by default), the liquid column breaks away: the chamber fills with vapour bubbles, the plate turns red and the indicator diagram is held flat at the separation line. The readouts give the highest speed with no separation. When the suction column arrives fast enough to lift the cylinder above the delivery head at the end of the suction stroke, the status line reports negative slip. Fit an air vessel and the long pipe carries the mean flow: watch the liquid level in the vessel rise and fall and the indicator diagram flatten.
5 SI and Imperial
The SI | Imperial switch changes every length, head, flow, pressure and power on screen: mm and m, L/min, kPa and kW in SI; in, ft, US gpm, psi and hp in Imperial. The calculation and the practice problems follow it.
6 Explore, Practice & Quiz
Explore has sixteen cards in four groups: Parts & working, Types & discharge, Indicator diagram, and Air vessels & separation, several with a worked example. Practice draws a new problem each time from eight kinds (discharge of single- and double-acting pumps, slip, power, acceleration head, pressure at the start of suction, maximum speed without separation, and the air vessel), in the units on screen, with the full solution. The Quiz asks eight questions from a pool of eighteen.
7 Calculations, Export & Tips
Σ Calculations works through the pump on screen step by step. CSV saves one revolution (crank angle, piston travel, cylinder head, suction and delivery flow, crank torque); PNG or a right-click (long-press on a phone) saves the picture. Try the Long suction pipe: separation preset, then the same pump with air vessels.
Reciprocating Pump — Working, Indicator Diagram and Air Vessel
A reciprocating pump is a positive displacement pump: a piston or plunger moves to and fro in a cylinder and pushes out a fixed volume on every stroke. Where a centrifugal pump trades flow for head along its curve, a reciprocating pump keeps its flow almost whatever the delivery pressure, which is why it is used for boiler feed, hydraulic test pumps, high-pressure washers, oil-well and mud pumps and metering duty. This simulator runs the pump on a real slider-crank and works out the pressure in the cylinder at every crank angle, so you can see the indicator diagram, the acceleration head, separation and the effect of an air vessel rather than memorising them.
Parts of a Reciprocating Pump
- Cylinder and piston (or plunger), with rings or packing to seal it.
- Crank, connecting rod and crosshead: the slider-crank mechanism turns the motor’s rotation into the piston’s stroke L = 2r.
- Suction valve and delivery valve: spring-loaded non-return valves opened only by the pressure difference across them.
- Suction pipe from the sump and delivery pipe to the tank, often each with an air vessel next to the cylinder.
- Stuffing box (gland) where the piston rod leaves the cylinder, and a relief valve, because a positive displacement pump must never be run against a shut valve.
How a Reciprocating Pump Works
On the suction stroke the piston moves away from the valves. The pressure in the cylinder falls below the suction pipe’s, the suction valve lifts and atmospheric pressure on the sump pushes water up the pipe. On the delivery stroke the piston returns, the pressure rises above the delivery pipe’s, the suction valve shuts and the delivery valve lifts. A single-acting pump uses one face of the piston; a double-acting pump has valves at both ends and delivers on both strokes. The theoretical discharge is Qth = A L N / 60 for single acting and (2A − a) L N / 60 for double acting, where a is the piston rod’s area.
Slip and Coefficient of Discharge
A little liquid leaks back through the valves before they seat, so the actual discharge Qa is below Qth. Slip = (Qth − Qa)/Qth, and the coefficient of discharge Cd = Qa/Qth is about 0.95 to 0.98. Worked example. The lab rig in the simulator (bore 100 mm, stroke 150 mm, 40 rpm, single acting) has Qth = 7.854 × 10−3 × 0.150 × 40/60 = 7.85 × 10−4 m³/s = 47.1 L/min; if the tank fills at 45.6 L/min, slip is 3.2 % and Cd = 0.968. Negative slip, where Qa exceeds Qth, appears with a long suction pipe, a short delivery pipe and a high speed: the suction column’s momentum carries water straight through the delivery valve before the delivery stroke begins.
The Indicator Diagram, Acceleration Head and Friction Head
The indicator diagram is the absolute pressure head in the cylinder plotted against the piston’s travel. Ideally it is a rectangle between Hatm − hs and Hatm + hd, and its area times ρgA is the work per stroke. In a real pump the water in each pipe has to be accelerated and decelerated with the piston: the acceleration head ha = (Lp/g)(A/ap)ω²r cos θ tilts the suction and delivery lines, lowest at the start of the suction stroke and highest at the start of the delivery stroke, and adds no net work. The friction head, proportional to the square of the velocity, bows the lines out at mid-stroke and adds two-thirds of its peak value to the average head. The simulator draws the dashed ideal rectangle under the real loop so you can see both effects grow as you speed up or lengthen the pipes.
Separation and the Maximum Speed
At the start of the suction stroke the cylinder pressure is Hatm − hs − has,max. If that falls below about 2.5 m of water absolute, dissolved air and vapour come out and the column separates from the piston; when it rejoins, it hammers. Setting the two equal gives the highest speed. For the Long suction pipe preset (bore 150 mm, stroke 300 mm, suction pipe 9 m long and 75 mm bore, lift 4.5 m), with a long connecting rod, ω² = (10.3 − 4.5 − 2.5) × 9.81 / (9 × 4 × 0.15), so N = 23.4 rpm. The simulator’s connecting rod is five crank radii long, which raises the acceleration at the start of the stroke by 20 % and lowers the limit to 21.5 rpm, as its readout shows.
Flow from Single, Double, Duplex and Triplex Pumps
A single-acting pump delivers in half-sine pulses with a gap; more working chambers on one crankshaft at equal angles fill the gaps. The table gives the ratio of the peak and the lowest delivery to the mean, with a very long connecting rod and the rod area neglected, as the simulator computes it.
| Pump | Deliveries per revolution | Peak / mean flow | Lowest / mean flow |
|---|---|---|---|
| Single acting (simplex) | 1 | 3.142 (π) | 0 |
| Double acting (simplex) | 2 | 1.571 (π/2) | 0 |
| Duplex double acting, cranks 90° apart | 4 | 1.111 | 0.785 |
| Triplex single acting, cranks 120° apart | 3 | 1.047 (π/3) | 0.907 |
Air Vessels and the Power They Save
An air vessel is a closed chamber with air trapped above the liquid, fitted to the suction and delivery pipes close to the cylinder. The air cushion swallows the to-and-fro flow, so the long pipe carries an almost steady flow at the mean velocity: the acceleration head in it disappears and the friction head drops to that of the mean velocity. For a single-acting pump the mean velocity is 1/π of the peak, so the friction work falls from ⅔hf,max to hf,max/π², a saving of 84.8 %; for a double-acting pump the saving is 39.2 %. In the simulator the vessel is an isothermal gas cushion, pV = constant, so a bigger gas volume gives a smaller pressure ripple. The Same pump with air vessels preset runs the separating pump safely and raises its maximum speed more than tenfold.
Who Uses This Simulator?
Diploma and undergraduate mechanical and civil engineering students in fluid mechanics and hydraulic machines courses, who are asked to sketch the indicator diagram, find the maximum speed without separation or the power saved by an air vessel; marine engineering cadets learning reciprocating bilge and ballast pumps; oil-field and process trainees meeting triplex plunger and duplex mud pumps; and instructors who want to show the cycle running instead of drawing it on a board. It sits beside the site’s centrifugal pump test rig for the comparison every syllabus asks for.
Frequently Asked Questions
How does a reciprocating pump work?
A crank and connecting rod move a piston to and fro in a cylinder. When the piston moves away from the valves the cylinder pressure falls, the suction valve lifts and liquid is drawn in from the suction pipe; when it moves back the pressure rises, the suction valve shuts, the delivery valve lifts and the liquid is pushed into the delivery pipe. Each stroke displaces a fixed volume, so it is a positive displacement pump.
What is the indicator diagram of a reciprocating pump?
It is the absolute pressure head in the cylinder plotted against the piston's travel over one revolution. Ideally it is a rectangle between the suction line (atmospheric head minus the suction lift) and the delivery line (atmospheric head plus the delivery head). The acceleration head tilts both lines, lowest at the start of each stroke, and the friction head bows them at mid-stroke. The enclosed area, times rho g A, is the work done per stroke.
What is the purpose of an air vessel in a reciprocating pump?
An air vessel is a closed chamber with air above the liquid, fitted to the suction and delivery pipes close to the cylinder. The air cushion absorbs the varying flow, so the long pipes carry an almost steady flow at the mean velocity. This removes the acceleration head, lets the pump run faster without separation, and cuts the friction work in the pipes by 84.8 percent for a single-acting pump and 39.2 percent for a double-acting pump.
Explore Related Simulators
- Centrifugal Pump Test Rig: the rotodynamic pump, its head-capacity curve, NPSH and affinity laws.
- Slider-Crank Mechanism: the mechanism that drives the piston, with piston velocity and acceleration.
- Fluid Flow in Pipes: the friction factor and the head loss in the suction and delivery pipes.
- Hydraulic Cylinder Simulator: a piston in a cylinder driven by oil pressure instead of driving it.
Updated