Parallelogram Law of Forces Simulator
Gravesand’s apparatus — find an unknown weight with the parallelogram of forces • 2D & 3D
- 1 Load
- 2 Release
- 3 Mark
- 4 Draw
- 5 Result
Display Controls
Σ Live equation — the forces at the knot on screen
1 Overview
A virtual Gravesand’s apparatus for the parallelogram law of forces: a vertical board with two pulleys, two weight hangers on strings and an unknown weight hanging from the knot where the strings meet. You do the whole experiment — load, release, mark the strings on the paper, draw the parallelogram to scale and measure the diagonal — and the simulator reveals the true weight and your percentage error. It has four modes: Simulate, Explore, Practice and Quiz, and a 2D and a 3D view.
2 Getting Started
The five lab steps run along the top of the canvas (Load, Release, Mark, Draw, Result). The green button under the canvas always does the next step. Set the two hangers in card 1 (each total includes the 50 g hanger), pick the unknown weight in card 2, then press Release the knot. Press 🎓 Show me to watch the whole experiment done for you, step by step.
The page opens in the 3D view on a computer or tablet and in the 2D view on a phone. The 2D | 3D switch is at the left of the bar under the canvas and the page remembers your choice; ?view=2d or ?view=3d in a link opens a particular view.
3 Simulate: the experiment
- Release — the knot swings and settles where the three forces balance. The strings run over real pulleys and the hangers rise and fall as the knot moves. With Pulley friction at 1 % or 3 % the pulleys stick and the knot can stop a little short of the true rest point: press Tap the board and it creeps the rest of the way. You can also drag the knot aside and let it go.
- Mark — click on a string where it crosses the paper to put a pencil dot under it, two dots on each of the three strings. Spread them out. With the mirror strip on, each dot lands on the string within about 0.3 mm; with it off, parallax throws it up to 2 mm sideways. Mark for me places good dots.
- Draw — the paper comes off the board. Step through: join the dots, mark OA = P and OB = Q to the drawing scale (card 3 suggests the largest scale that fits), complete the parallelogram with a set square, draw the diagonal OC and measure it on a millimetre rule.
- Result — the unknown weight W = OC × scale, the angle of OC from the vertical, the analytical check R = √(P² + Q² + 2PQ cos θ) with your measured θ, the true weight and your percentage error. Record adds the row to the observation table; change the loads and repeat for a mean.
If the unknown weight is too heavy (W ≥ P + Q) or one hanger outweighs the other two, there is no equilibrium and the simulator shows what really happens: the knot runs to a pulley or the weight sinks until something jams.
4 2D and 3D views
In 2D the board is seen from the front, with the forces at the knot drawn beside it: P, Q and W as arrows to scale and their live parallelogram, so you can watch the diagonal swing into line with the weight as the knot settles. In 3D the apparatus stands on a lab bench: drag to turn it, Ctrl + scroll or pinch to zoom, click the strings to mark them, and watch the paper come off the board onto the bench for the drawing. Display Controls (top-left of the canvas) switch the force arrows, the live parallelogram, the angles and the labels.
5 Explore, Practice & Quiz
Explore has sixteen cards in four groups: The law, Formulas, The experiment, and Errors & uses. Practice mixes eight kinds of problem (resultant, its direction, the unknown weight, the angle between the strings, Lamy’s theorem, reading the diagonal, percentage error and the hanger load), each with a worked solution. Quiz asks six questions drawn at random from twenty, with the options shuffled, and scores you with up to three stars.
6 Key Concepts
With P = 250 gf, Q = 300 gf and Block A (380 gf) the strings meet at θ = 93.1°: R = √(250² + 300² + 2 × 250 × 300 × cos 93.1°) = 380 gf. At 1 cm = 25 gf, OA = 10.0 cm, OB = 12.0 cm and the diagonal OC = 15.2 cm. In newtons the same loads are 2.45 N, 2.94 N and 3.73 N (g = 9.81 m/s², the value lab manuals use). Choose Forces in: gram-force to work in gf as many school manuals do; the masses are always in grams.
7 Tips & Other Features
Keep the knot near the middle of the paper: if it rests off the sheet, change P or Q. Mark the dots as far apart as you can. Σ Calculations shows the full working of the current reading, PNG or a right-click (long-press) saves the view, and CSV downloads the observation table. Clicks and a soft thud give sound feedback when the knot is released and the paper is marked.
Parallelogram Law of Forces — a Virtual Gravesand’s Apparatus
The parallelogram law of forces says how two forces acting at one point combine. Draw the two forces from the point as adjacent sides of a parallelogram, to scale and in their own directions: the diagonal through the same point is their resultant, in size and direction. This simulator is the classic laboratory proof of the law, Gravesand’s apparatus, used to find an unknown weight. Everything happens as it does at the bench: the knot settles, you mark the strings, take the paper off, draw the parallelogram and measure the diagonal.
The Law and Its Formula
If forces P and Q act at an angle θ to each other, the cosine rule on the parallelogram gives the size of the resultant and its angle φ from P:
- R = √(P² + Q² + 2PQ cos θ)
- tan φ = Q sin θ / (P + Q cos θ)
At θ = 0° the forces add (R = P + Q), at 180° they subtract, and at 90° R = √(P² + Q²). The law holds for every vector quantity: force, velocity, displacement, acceleration. Half of the parallelogram is the triangle law, and three forces in equilibrium close a triangle tip to tail, which leads to Lamy’s theorem: each force is proportional to the sine of the angle between the other two.
How to Find an Unknown Weight
The knot of the apparatus is held by three forces: the two string tensions P and Q, equal to the hanging weights when the pulleys run freely, and the unknown weight W. At rest they balance, so W is the equilibrant of P and Q: equal and opposite to their resultant. Mark each string with two pencil dots, using a mirror strip to avoid parallax, join them and extend the lines to meet at O. Mark OA = P and OB = Q to a scale such as 1 cm = 25 gf, complete the parallelogram OACB, and the diagonal OC, read on a millimetre rule and multiplied by the scale, is the unknown weight. It should point straight up, along the third string.
| P (gf) | Q (gf) | θ between the strings | Scale | OA, OB (cm) | OC (cm) | W = OC × scale |
|---|---|---|---|---|---|---|
| 250 | 300 | 93.1° | 1 cm = 25 gf | 10.0, 12.0 | 15.2 | 380 gf |
| 200 | 200 | 82.8° | 1 cm = 20 gf | 10.0, 10.0 | 15.0 | 300 gf |
| 350 | 400 | 92.5° | 1 cm = 50 gf | 7.0, 8.0 | 10.4 | 520 gf |
Each row is an equilibrium the simulator’s own engine reaches: for P = 200 gf and Q = 200 gf with a 300 gf weight the two strings make 41.4° with the vertical, and the knot hangs 32 cm below the pulleys.
Sources of Error and Precautions
The largest error is pulley friction. A sticking pulley lets the string tension at the knot differ from the hanging weight, so the knot can rest anywhere in a small region; tapping the board lets it settle at the true point. Set the friction to 3 % in the simulator and compare a reading before and after tapping. The next is drawing: dots marked close together, parallax and a thick pencil line all turn the string lines, and an error in angle grows in the diagonal. Finally, P and Q must include the hanger; leaving its 50 g out shortens both sides of the parallelogram. A good reading agrees with the true weight within 2–3 %, and repeating with three different loads and taking the mean reduces the scatter.
Gravesand’s Apparatus and the Force Table
The vertical board takes its name from Willem ’s Gravesande, the Leiden professor who demonstrated Newton’s mechanics with apparatus of this kind in the early eighteenth century. Many US and European college labs use a horizontal force table instead: pulleys clamped round a circular table at chosen angles pull on a central ring, and the third force is adjusted until the ring sits centred. The physics at the ring is exactly the physics at the knot here: three concurrent forces whose vector sum is zero, the resultant of two of them balanced by the third.
Who Uses This Simulator?
Students doing the “verification of the parallelogram law of forces” or “vector addition of forces” practical in high school physics (CBSE, ICSE, GCSE and A-level, IB) and in first-year engineering mechanics or college physics labs; teachers who want to show the whole experiment on a projector before the lab; and anyone revising the parallelogram law, the triangle law and Lamy’s theorem.
Frequently Asked Questions
What is the parallelogram law of forces?
If two forces acting at a point are represented in size and direction by the two adjacent sides of a parallelogram drawn from that point, their resultant is represented in size and direction by the diagonal of the parallelogram through the same point. Its size is R = sqrt(P^2 + Q^2 + 2PQ cos theta), where theta is the angle between the forces.
How do you find an unknown weight with Gravesand’s apparatus?
Hang known weights P and Q over the two pulleys and the unknown weight from the knot. When the knot is at rest, mark the directions of the strings on the paper behind them. Draw OA = P and OB = Q to a chosen scale along the string lines, complete the parallelogram and measure the diagonal OC. The unknown weight is OC multiplied by the scale, and the diagonal should be vertical.
Why does the unknown weight have to be less than P + Q?
The resultant of two forces can never be more than their sum (when they act in the same direction) or less than their difference. If the unknown weight is P + Q or more, no angle between the strings can balance it: it sinks and pulls both hangers up to their pulleys.
Explore Related Simulators
- Free Body Diagram & Force Resolver: resolve any set of concurrent forces into components and find the resultant.
- Newton’s Laws Simulator: forces, mass and acceleration on the bench, including tensions in strings over pulleys.
- Truss Analysis: the same balance of forces at every joint of a bridge or roof truss.
- Simple Machines: pulleys, levers and inclined planes, and the forces they trade.
- Friction Simulator: static and kinetic friction, the error source that sticks the pulleys.
- Torque & Rotation: when forces do not meet at one point and turn a body instead.
Updated