MechSimulator

Spherometer Simulator

Radius of curvature of lenses & mirrors in 3D — Simulate • Explore • Practice • Quiz

Mode
Units
Display Controls
Reading aids
3D

Σ Live working — from the readings on screen
User Guide — Spherometer Simulator
1 Overview

The simulator is a laboratory spherometer: three pointed legs, a central screw with a circular scale on its head, and an upright main scale. Stand it on a surface, turn the screw until the tip just touches, and read the two scales. The reading on a plane glass plate and the reading on a curved surface give the sagitta h, and the radius of curvature follows from R = l²/6h + h/2. It has four modes: Simulate, Explore, Practice and Quiz.

2 Getting Started

Choose an instrument in card 1 and a surface in card 2. Turn the screw with the buttons under the picture (↑ Raise and ↓ Lower move one division and repeat while held; ⤒ and ⤓ move a full turn), by dragging the knurled head left and right, or with the arrow keys and Page Up / Page Down when the picture has focus. ↧ Lower to touch lowers the screw slowly and stops on the division where the tip just touches. Press ✎ Record to write the reading into the table in card 3.

The page opens in the 3D view on a computer or tablet and in the 2D view on a phone. The 2D | 3D switch is at the left of the bar under the picture, and the page remembers your choice. Add ?view=2d or ?view=3d to a link to open a particular view.

3 Simulate Mode
  • Surfaces: a plane glass plate, a convex lens, a concave mirror, a concave lens, a watch glass, a steel ball and a custom surface whose radius and shape you set.
  • The 2D view shows the spherometer standing on the surface (in section, at true size), a close-up of the main scale with the edge of the disc against it, a close-up of the circular scale at its index, and Detail A: the tip and the surface magnified, with the gap printed.
  • Turning too far lifts the instrument: the screw pushes the frame up, one leg leaves the surface and the spherometer rocks on the tip. The leg is drawn lifted and the reading is marked as too far. Raise the screw until all three legs sit again.
  • The 3D view: drag the knurled head left or right to turn the screw, drag anywhere else to orbit, Ctrl + scroll or pinch to zoom. Whole, Scales and Tip move the camera.
4 Taking the Readings

Stand the spherometer on the plane glass plate, lower the screw to touch and record. Raise the screw, stand it on the curved surface, lower to touch and record again. The table then shows h = |surface reading − plate reading| and the radius. A reading above zero belongs to a convex surface and one below zero to a concave surface. Below zero the circular scale is read as (N − c), and the status line says so.

▶ Show me how runs the whole experiment for the surface on screen, one step at a time, using the same controls. Any button or drag stops it.

5 SI and Imperial Instruments

The SI | Imperial switch changes the instrument, not just the labels. In SI there are two metric spherometers, 1 mm pitch × 100 divisions and 0.5 mm pitch × 50 divisions, both reading 0.01 mm, with legs 40.00 mm apart. In Imperial the spherometer has a 40 threads-per-inch screw (pitch 0.025″) with 25 divisions, reading 0.001″, a main scale graduated in 0.025″ and numbered in tenths of an inch, and legs 1.500″ apart. The surfaces change to inch sizes too. The choice is remembered across the site.

6 Explore, Practice & Quiz

Explore has sixteen cards in four groups: The instrument, Taking a reading, The formula and Errors & good practice, each with a worked example. Practice has three kinds: Read the scales (the reading tiles are hidden; type the reading, with a minus sign below zero), Measure a surface (a surface of unknown radius and an unknown zero error: take the readings and enter R) and Calculations (ten kinds of problem in the unit system you have chosen). Quiz asks six questions drawn from a pool of twenty, with the options shuffled, and scores you with up to three stars.

7 Zero Error & Tips

Set a zero error in card 3 (−5 to +5 least counts). The plate reading then shows it, and the difference method removes it from h. Make the last approach to contact downwards each time, as you would to avoid backlash on a real screw. Σ Calculations shows the working for the readings in the table; PNG or a right-click (long-press) saves the picture or copies the readings. A soft tick sounds for each division and a click on contact.

Spherometer — How to Read It and Find the Radius of Curvature

A spherometer measures the radius of curvature of a spherical surface: a lens, a mirror, a watch glass or a ball. It is a fine screw, like the one in a micrometer screw gauge, set upright through the middle of a three-legged frame. The screw measures how far the centre of the surface rises above, or falls below, the plane of the three legs. That height is the sagitta h, and with the leg spacing l it gives the radius. This simulator puts the instrument on six surfaces in 2D and 3D, in metric and inch versions, and does every reading the way it is done in the laboratory.

Parts of a Spherometer

Least Count and Reading the Scales

The least count is the pitch divided by the number of circular divisions. Above zero, the reading is the whole main-scale divisions the disc has passed, times the pitch, plus the circular division at the index times the least count. Below zero the disc has turned the other way, so the number at the index counts up from the next division: the reading is the whole divisions below zero plus (N − c) circular divisions.

InstrumentPitchCircular divisionsLeast countLeg spacing
Metric, 1 mm × 1001 mm1000.01 mm40.00 mm
Metric, 0.5 mm × 500.5 mm500.01 mm40.00 mm
Inch, 40 TPI × 250.025 in250.001 in1.500 in

The Spherometer Formula: R = l²/6h + h/2

The three leg tips lie on a circle of radius r = l/√3. On a sphere of radius R, the centre of the surface stands h above the plane of that circle, and the right triangle from the centre of the sphere gives (R − h)² + r² = R². So 2Rh = r² + h² and

R = r²/2h + h/2 = l²/6h + h/2

The sagitta h is found by the difference method: one reading with the tip just touching the curved surface, one on a plane glass plate, and h is their difference. Any zero error is in both readings and cancels. The table shows what a spherometer with legs 40.00 mm apart reads on the surfaces in the simulator.

SurfaceRadius RSagitta h (legs 40.00 mm)Reading on a 0.01 mm spherometer
Concave mirror300 mm0.890 mm−0.89 mm
Convex lens200 mm1.338 mm+1.34 mm
Concave lens100 mm2.703 mm−2.70 mm
Watch glass50 mm5.653 mm+5.65 mm
Steel ball Ø 80 mm40 mm7.340 mm+7.34 mm

Worked example. The plate reading is 0.00 mm and the convex lens reads 1.34 mm, so h = 1.34 mm. R = 40.00²/(6 × 1.34) + 1.34/2 = 1600/8.04 + 0.67 = 199.0 + 0.67 = 199.7 mm, within the 0.01 mm reading of the 200 mm the lens was made to. On a strongly curved surface the h/2 term matters: dropping it on the watch glass gives 47.2 mm instead of 50.0 mm.

From Radius to Focal Length

For a spherical mirror the focal length is half the radius: the 300 mm concave mirror has f = 150 mm. For a thin symmetric lens of refractive index n the lensmaker’s equation gives f = R/2(n − 1), so a glass lens (n = 1.5) has f ≈ R. Opticians quote a surface’s power in dioptres, P = (n − 1)/R with R in metres; the lens clock (Geneva lens measure) used in American and European optical shops is a spherometer whose dial is graduated directly in dioptres.

Sources of Error

Printable Spherometer Worksheet (PDF)

The Worksheet button beside Calculations and PNG builds a printable spherometer worksheet in your browser. Choose millimetres or inches first: the metric sheet uses the 1 mm × 100 and 0.5 mm × 50 spherometers (0.01 mm, legs 40.00 mm apart), the inch sheet the 40 TPI × 25 spherometer (0.001 in, legs 1.500 in apart), never converted numbers. Then pick a level. Foundation covers the parts, the least count, readings above zero and the radius from l and h; Standard adds readings below zero (N − c), the difference method with a zero error and r = l/√3; Advanced adds a negative zero error, the h/2 term, the focal length of a mirror and the power of a lens surface in dioptres. The scale close-ups are drawn with the simulator’s own engravings, one question is a task done on the simulator, and the presets are a quick check, a class test, a simulator homework and the full sheet. Every version number prints new readings with a matching answer key, and nothing you type leaves your computer.

Who Uses This Simulator?

Students doing the spherometer experiment in school and introductory college physics (CBSE and state boards, A-level and IB practical work, and optics labs in the United States and Europe); instructors who want to show the two scales and the below-zero reading in close-up; and anyone learning how a lens clock or a ring spherometer measures curvature in an optical workshop.

Frequently Asked Questions

How do you read a spherometer?

Count the whole divisions the disc has risen above zero on the upright main scale and multiply by the pitch, then add the circular-scale division at the edge of the main scale multiplied by the least count. Below zero, use the whole divisions below zero plus (N minus the circular reading) times the least count, where N is the number of circular divisions.

What is the formula of a spherometer?

The radius of curvature is R = l^2/6h + h/2, where l is the distance between two legs and h is the sagitta, the height of the centre of the surface above the plane of the three legs. It comes from (R - h)^2 + r^2 = R^2 with r = l/sqrt(3), the radius of the circle the legs stand on.

What is the least count of a spherometer?

The least count is the pitch of the screw divided by the number of divisions on the circular scale. A 1 mm pitch with 100 divisions, or a 0.5 mm pitch with 50 divisions, gives 0.01 mm; an inch spherometer with 40 threads per inch and 25 divisions gives 0.001 in.

Is there a printable spherometer worksheet?

Yes. Press Worksheet under the spherometer controls to download a printable spherometer worksheet with an optional answer key, in millimetres (1 mm and 0.5 mm screws, 0.01 mm) or inches (40 TPI, 0.001 in), at Foundation, Standard or Advanced level. The questions are drawn from the simulator: name the parts, find the least count, read the main and circular scales above and below zero, spot the N minus c mistake, find the sagitta by the difference method, work out the radius of curvature and (Advanced) the focal length and the power in dioptres, plus one task done on the simulator. Every version number gives new readings, and the PDF is made in your browser.

Explore Related Simulators

Updated