MechSimulator

Sine Bar Simulator

Set angles with gauge blocks in 3D — Simulate • Explore • Practice • Quiz

Mode
Units
Display Controls
Bench
3D

▦
Click a block to wring it on, click again to take it off
Σ Live working — from the bench on screen
User Guide — Sine Bar Simulator
1 Overview

The simulator is a sine bar on a granite surface plate: a steel bar with two rollers whose centres are exactly L apart, a case of gauge blocks, a workpiece and a plunger dial gauge on a magnetic stand. Set an angle by standing one roller on a stack of height H = L sin θ, then check a workpiece by traversing the dial along its top. It has four modes: Simulate, Explore, Practice and Quiz.

2 Getting Started

Type the angle in card 1 (degrees, minutes, seconds) or use the slider and the ±1° / ±1′ buttons. ▦ Build stack wrings the fewest blocks that make H. To build it yourself, click blocks in the case in card 3: each click wrings that block onto the stack named by the Onto high / low stack switch, and a second click (or a click on it in the stack list) takes it off. Choose the bar, the set and the bar’s condition in card 2.

The page always opens in the 2D view. Switch to 3D with the 2D | 3D switch at the left of the bar under the picture; in 3D the View buttons on the picture (Whole, Stack, Dial) show what each camera looks at. Add ?view=3d to a link to open the 3D view directly.

3 Simulate Mode
  • The 2D view shows the bench in elevation at true scale, a close-up of both stacks with every block named, and the face of the dial gauge.
  • Workpieces (card 4): an angle wedge, a 1:20 taper plug gauge, an angle gauge block of 30°, or no workpiece. Choosing one sets the angle to its nominal value.
  • The dial gauge hangs plunger-down over the work with its face to the front, on a magnetic stand whose column stands behind the bar, as it is set up on a real surface plate. To A and To B move it to two points ℓ apart, the arrows move it a little, and you can drag the stand along the plate. Zero sets the dial to zero where it is; Record writes the reading at A or B into the table.
  • Bar condition puts a centre-distance error or an undersize roller into the bar, so the bar stands at a slightly different angle from the one the formula gives. The dial finds it on the angle gauge block.
  • The 3D view: the names are printed on the parts themselves (Labels in Display Controls turns them off); drag the dial stand to move it, drag anywhere else to orbit, Ctrl + scroll or pinch to zoom. Whole, Stack and Dial move the camera.
4 Checking a Workpiece

With the bar set to the work’s nominal angle, record the dial at A, move to B and record again. The table shows the rise Δ = B − A, the work’s angle α = θ − tan⁻¹(Δ/ℓ) and the stack that would make the work level. ▶ Show me how runs the whole job for the work on screen: the height, the stack block by block, the dial at A and at B. Any button stops it.

5 SI and Imperial

The SI | Imperial switch changes the equipment, not just the labels. In SI there are 100 mm and 200 mm bars and three metric sets as workshops buy them: the 88-piece BS 4311 set (with its 1.0005 mm block, 0.0005 mm steps), the 87-piece ISO 3650 / DIN 861 set (0.001 mm steps) and the 47-piece set (0.005 mm steps), with a plunger dial gauge graduated in 0.001 mm (0.1 mm a revolution, with a revolution counter). In Imperial there are 5 in and 10 in bars and the 81-piece inch set (.1001–.1009, .101–.149, .050–.950 and 1–4 in, in .0001 in steps), a real inch set and not converted millimetres, with a dial gauge graduated in .0001 in (.010 in a revolution). The choice is remembered across the site.

6 Explore, Practice & Quiz

Explore has sixteen cards in four groups: The sine bar, Gauge blocks, Setting & checking and Errors & good practice, each with a worked example. Practice has three kinds: Build the stack (wring the blocks for an angle by hand; the check says whether you used the fewest), Find the angle (a wedge of unknown angle: set the bar, traverse the dial and enter α in degrees or as d m s) and Calculations (ten kinds of problem in the unit system you have chosen). Quiz asks six questions drawn from a pool of twenty, with the options shuffled, and scores you with up to three stars.

7 Tips

The status line warns above 45°, where a stack error turns the bar more. Σ Calculations shows the whole working, including the stack built finest decimal first; PNG or a right-click (long-press) saves the picture or copies the readings. A soft click sounds as each block is wrung on.

Sine Bar — How to Set an Angle with Gauge Blocks

A sine bar sets or measures an angle to a few seconds of arc using nothing but lengths: the exact distance between its two rollers and the exact height of a stack of gauge blocks (slip gauges). It is the standard way to set up angular work for inspection, grinding or marking out in a toolroom or metrology laboratory. This simulator puts the bar, the blocks, the work and a plunger dial gauge on a surface plate in 2D and 3D, in metric and inch versions.

Parts of a Sine Bar

The Sine Bar Formula: sin θ = H / L

The line of the roller centres, the surface plate and the stack under the high roller form a right triangle. The line of centres is the hypotenuse L and the stack is the opposite side H, so sin θ = H / L, and to set an angle H = L sin θ. Each roller touches the plate or the stack directly below its centre, so the roller diameter cancels as long as both rollers are the same size. The table gives the stacks for common angles.

AngleH, 100 mm barH, 200 mm barH, 5 in barStack for 100 mm (88-piece set)Turn per 1 µm of stack (100 mm)
5°8.7156 mm17.4311 mm0.4358 in1.0005 + 1.005 + 1.21 + 5.52.07″
10°17.3648 mm34.7296 mm0.8682 in1.005 + 1.36 + 5 + 102.09″
15°25.8819 mm51.7638 mm1.2941 in1.002 + 1.38 + 3.5 + 202.14″
20°34.2020 mm68.4040 mm1.7101 in1.002 + 1.2 + 2 + 302.20″
30°50.0000 mm100.0000 mm2.5000 in502.38″
45°70.7107 mm141.4214 mm3.5355 in1.0005 + 1.21 + 8.5 + 602.92″
60°86.6025 mm173.2051 mm4.3301 in1.0005 + 1.002 + 1.1 + 3.5 + 804.13″

Building a Gauge Block Stack

Gauge blocks are wrung together into a stack whose height is the sum of the blocks. A set holds one of each size, so the stack must be found from the sizes available. Choose the block that clears the last decimal place first, then the next place, and finish with the large blocks: this gives the fewest blocks, and fewer wrung joints mean a more accurate, less worn stack.

Worked example. 23° 15′ on a 100 mm bar needs H = 100 × sin 23.25° = 39.4744 mm, built to 39.4745 mm from the 88-piece set. Take 1.0005 (38.474 left), 1.004 (37.47 left), 1.47 (36 left), 6 (30 left) and 30: five blocks. The bar then stands at 23° 15′ 00.3″.

SetSeriesBuilds in steps of
88-piece metric (BS 4311)1.0005; 1.001–1.009; 1.01–1.49; 0.5–9.5; 10–100 mm0.0005 mm
87-piece metric (ISO 3650 / DIN 861)1.001–1.009; 1.01–1.49; 0.5–9.5; 10–100 mm0.001 mm
47-piece metric1.005; 1.01–1.09; 1.1–1.9; 1–24; 25, 50, 75, 100 mm0.005 mm
81-piece inch (ASME B89.1.9).1001–.1009; .101–.149; .050–.950; 1–4 in.0001 in

Small Angles and Large Angles

A height smaller than the thinnest block cannot be built on its own, so for very small angles both rollers are lifted on stacks and the difference H₁ − H₂ is made equal to L sin θ. At large angles the bar becomes sensitive: a height error δH turns it by δH / (L cos θ), which at 60° is twice the error at 0°. Sine bars are normally used below 45°; larger angles are set from the complement or with angle gauge blocks.

Checking a Taper or Wedge with a Dial Indicator

Set the bar to the angle the work should have and push the work against the stop. Traverse a plunger dial gauge on a magnetic stand a distance ℓ along the work’s top. If the work is right the dial does not move. If it rises Δ, the work’s angle is α = θ − tan⁻¹(Δ / ℓ), and a stack of L sin α would make it level. A taper plug gauge is checked with the bar set to its included angle, since its lower edge lies on the bar and its upper edge is the included angle above it.

Worked example. The bar is at 23° 15′ and the dial rises 0.010 mm over ℓ = 50 mm: tan⁻¹(0.010/50) = 0.01146° = 41″, so the work is 23° 14′ 19″.

Sources of Error

Who Uses This Simulator?

Students of engineering metrology and inspection in technical colleges and apprenticeships (CTE and machining programs in the United States, metrology units in the UK and Europe, and diploma and degree courses in India); instructors who want to show a stack being built block by block; and machinists checking how a sine plate or sine centre is set up.

Printable Sine Bar Worksheet (PDF)

The Worksheet button in the simulator's control panel makes a printable A4 sine bar worksheet for a class. Choose the units first (the 100 mm and 200 mm bars with the 88, 87 and 47-piece metric sets, or the 5 in and 10 in bars with the 81-piece inch set), then the level: Foundation (parts, degrees, minutes and seconds, H = L sin θ, reading and building a stack, reading two dial faces), Standard (adds two stacks for a small angle, the 1/cos θ sensitivity and the work’s angle from the dial) or Advanced (adds the corrected stack and the bar’s own errors). Every picture is drawn from the simulator’s geometry and every stack is the fewest blocks its solver finds. Pick a quick check, a class test, a simulator homework or the full sheet; each version number gives new numbers, and the answer key states what to accept. Nothing you type in the dialog leaves your browser.

Frequently Asked Questions

What is the formula of a sine bar?

sin θ = H / L, where L is the distance between the centres of the two rollers and H is the height of the gauge-block stack under one roller (or the difference between two stacks). To set an angle, H = L sin θ; a 100 mm bar set to 30° needs a 50 mm stack.

How do you build a gauge block stack for a sine bar?

Work out H = L sin θ and round it to what the set can build. Then pick the block that clears the last decimal place first, then the next decimal, and finish with the large blocks. With the 88-piece metric set, 39.4745 mm is 1.0005 + 1.004 + 1.47 + 6 + 30 mm: five blocks, the fewest possible.

Why is a sine bar not used above 45 degrees?

A height error δH turns the bar by δH / (L cos θ). As the angle grows cos θ falls, so the same small error in the stack makes a larger error in the angle: 1.41 times larger at 45° than at 0°, and twice as large at 60°.

How do you check a taper with a sine bar?

Set the bar to the angle the work should have, put the work on the top face against the stop, and traverse a dial indicator a distance ℓ along its top. If the dial rises Δ, the work's angle is θ − tan⁻¹(Δ/ℓ). A taper plug gauge is checked the same way with the bar set to its included angle.

Is there a printable sine bar worksheet?

Yes. The Worksheet button in the simulator's control panel makes a free A4 PDF in millimetres or inches, at Foundation, Standard or Advanced level: parts of a set-up, H = L sin θ, reading and building gauge-block stacks with the fewest blocks, two stacks for small angles, why sine bars stay below 45°, checking a workpiece from two dial readings, the bar's own errors and a task on the simulator. Every version has new numbers and an optional answer key.

Explore Related Simulators

Updated